Anaheim PROGRAMMABLE SIMPLE INDEXER/DRIVER MBC10SI1 Instrukcja Użytkownika

1#L010185 June 2007MBC10SI1Programmable Simple Indexer/DriverUser’s Guide910 East Orangefair Lane, Anaheim, CA 92801e-mail: [email protected]

10#L010185 June 20078 Lead MotorsSeries Connection: When configuring the motor windings in series, use the per phase (or unipolar)current rating to de

11#L010185 June 2007FunctionsHard Limit Switches: When a hard limit switch is encountered, the pulses will stop. Hard limits areintended as an emergen

12#L010185 June 2007SMPG-SMSI SoftwareThe SMPG-SMSI software is a handy utility that supports Anaheim Automation’s programmable pulsegenerators and si

13#L010185 June 2007“The Unit is Connected” / “The Unit is NOT Connected”On the right of the Toolbar, the user will find the communication status of t

14#L010185 June 2007Program WindoweliforPnoitoM2ro,1seliforpnoitomtceleSleceD/leccAdneS ces/spets(.rexedniehtotretemarapnoitareleced&noitareleccae

15#L010185 June 2007Direct mode is used to directly control the motion for real time movements through serial communication.The indexer has 14 command

16#L010185 June 2007$ - Version Number RegisterFormat: $Description: This command requests the indexer to return the version number.! - Error Codes R

17#L010185 June 2007C - Current Reduce OptionFormat: C# - where # is 0 or 1Description: This command enables the driver to reduce current after pulses

18#L010185 June 2007S - Stop SoftFormat: SDescription: This command will cause the indexer to ramp down to base speed and rununtil the index is comple

19#L010185 June 2007Visual Basic Direct Mode Programming ExamplesExample 1: This Example is for Axis=0, and Profile=1DimConst DefaultTimeout As Single

2#L010185 June 2007IntroductionThe MBC10SI1 is an low cost single axis step motor driver integrated with a programmable simple indexer.The MBC10SI1 mi

20#L010185 June 2007TroubleshootingProblem:Can not establish communications with the indexer.Possible Solutions:1) Make sure the indexer has power. Is

21#L010185 June 2007edoCrorrE epyT noitpircseD1wolfrevOeveiceRrorrErorrelanretninasisihT.rorregniveiceradahsnoitacinummoclairesehT.retupmocehtybdesuac

22#L010185 June 2007CopyrightCopyright 2005 by Anaheim Automation. All rights reserved. No part of this publication may be repro-duced, transmitted, t

3#L010185 June 2007A) A Profile input is activated; Ramps up to max speed.B) No limit is active; Max speed is reached (keeps running at max speed).C)

4#L010185 June 2007LEDsWhen powered and operated properly, the status LED will be green. When a communication or programsyntax error occurs, the LED

5#L010185 June 2007Connector Description:2ProtcennoC#niP noitpircseD1)CDV0(dnuorGylppuSrewoP2)CDV08-CDV02(tupnIylppuSrewoP3)A(1esahProtoM4)A/(3esahPro

6#L010185 June 2007stnemeriuqeRegatloVCDV08-02)8dna7sniP(stupnIeliforPtratS)CDV0(woL)niP(tupnInoitceriDWC)nepO(hgiHWWC)CDV0(woL)niP(tupnIffO/nOnO)nepO

7#L010185 June 2007Wiring DiagramsDimensions and Jumper/Potentiometer Locations

8#L010185 June 2007Setting the Output CurrentThe output current on the MBC10SI1 is set by the on-board potentiometer R29 (Refer to Dimensions/Jumper a

9#L010185 June 2007Step Motor ConfigurationsStep motors can be configured as 4, 6, or 8 leads. Each configuration requires different currents. Refer t